Today saw me wanting to go activate a park as the weather was wonderful and I had a little time to go so I headed over to my usual location at US-2169 (Cloudland Canyon State Park) and went to the frisbee golf course parking lot. But then as you see in the sign below, it says Ascalon Trailhead… Well, read on to see why.
Meet N4ARV (Anthony) who was setup with his FX-4CR portable station. He had already strung a nice long wire up into a nearby tree to work some POTA SSB in my usual spot! We chatted for a few minutes and we agreed that since I also wanted to work 20 meters (he was already on 20 at this point) that I would head over to the Ascalon Road Trailhead to prevent our radios from overloading each others receivers. I could have probably just went down to the canyon rim lot, but I knew Ascalon would be quieter so I hopped in the truck and was on my way.
Anthony had a really tidy little kit that he was operating out of today, the battery was really small too. It was right up my alley… haha. Just what I need, another radio…The FX-4CR is a powerhouse of a machine too. It is loaded with features that would make a full size radio blush! He was working SSB and it looked like he was not struggling at all either. Hope to meet him again at some point.
Once you get to the Ascalon Road trailhead, you are greeted with a little reminder to pay for your parking. I am exempt from all this mess though as I buy the annual pass, which for a POTA op, is worth it’s weight in gold since you will be in parks all the time.
I think I have activated 42 or 44 Georgia parks so far on this pass. If I had used the kiosk each time that would have been over 200 dollars in parking fees. Instead I have my annual pass which is only 50$ and my renewal isn’t till July. Last year I got over 100 activations on that pass making average parking costs only 50 cents per visit…not bad for what you get access to.
As you can see below, I pretty much had the place to myself. There were a few people that are behind my truck and are out of camera frame, but midday on a weekday is when I like to activate as you get the run of the place for the most part. I found a shady spot and parked there so I could setup on the bedcover, but as it turns out, the truck was on a slope that made the shady side about 5 feet off the ground. I knew at this point that I had to get creative with the radio location. I have setup like this once before already and I think it was with the same radio too, but today I setup with the whole little mini-station and it still fit!
Meet the “Tire Station” location of my POTA setups. I only have about 4 locations that I use. The truck cab, the bed cover, a random picnic table (basically I will use any available picnic table) and the “tire” station. I don’t think I have setup anywhere else in over a year other than these four positions. It works well with a folding camp chair, which I keep in the truck. It is also at the perfect height for my CW listening operations so I don’t need headphones as long as the rest of the area is still quiet.
Today also saw the introduction of a new piece of kit for me. The aviator knee clipboard… This widget is the perfect tool to hold my notebook and I could even stand up and get stuff out the pack or what ever and it would stay put. That was awesome to say the least, and is a great addition if you paper log like me. I don’t know how I got by so long with out it now that I have it.
As you can see, the clipboard make a little table of sorts that I can sit my stuff on and still work with the radio and such. I highly recommend this device for POTA ops. I got mine for Christmas, but if I had to guess, it probably came from Amazon… Just don’t forget that this “table” is attached to your leg and if you stand up, all the stuff on the table will go for flying lessons immediately.
I have memorized what the four knobs control, this frees me from having to look at them to control what they do. First knob is keyer speed, I use it to slow down for slower ops mostly, but I usually set it by ear anyway so I dont have to see it. Second knob is RF Power and it is set and forget, I dont change it during the activation at all. Thrid knob is RF gain and I use it to control the noise floor, I will usually turn it down a little to lower the band noise, but will turn it up to work a weak station. The last one is AF Gain (AKA Volume) and I use it a good bit, mainly when I get a really strong station coming in, I will back it down a little then, and then bring it back afterwards. But I use three of the four enough to memorize what they do so I don’t have to look at them. That is a huge benefit to such a simple radio, you simply memorize what each button, switch and knob do and you can operate the radio in the dark. I could run this radio blindfolded. I don’t think it will transmit out of band so I am pretty sure I could literally operate it blindfolded…only problem with that is then I couldn’t log…lol.
Another little addition to the radio that I really like is the S meter I built for it. I am thinking about changing the way it connects currently though as it needs the 3.5mm socket on the same side as the 4 pin plug. This would help tremendously with the arrangement of the little station at times and I really need to do it soon…lol. I also need to rework the power cable on the power box/speaker unit to be a little longer too, I dont know why I made that cable only 6 inches long.
Today saw a great run on 20 meters in the time I had allotted for the activation. As you can see below, I made 29 contacts in about 45 minutes at QRP power. Not bad for me. I enjoy the challenge of using small radios at these parks to make contacts like this. I will occasionally use larger radios too, but this is my jam…
I hope you enjoyed coming along for an activation with me and hope that I will work you on the air at some point.